TDA1675A PDF

TDAA Vertical Deflection Circuit. SYNCHRONISATION CIRCUIT ESD PROTECTED PRECISION OSCILLATOR AND RAMP GENERATOR POWER. View from ELEC 1 at Perm State University. TDAA VERTICAL DEFLECTION CIRCUIT SYNCHRONISATION CIRCUIT ESD. Find great deals for TDAA Vertical Deflection Circuit Original SGS. Shop with confidence on eBay!.

Author: Gadal Votaur
Country: Mauritius
Language: English (Spanish)
Genre: Science
Published (Last): 3 September 2008
Pages: 98
PDF File Size: 12.83 Mb
ePub File Size: 10.86 Mb
ISBN: 957-5-19581-460-3
Downloads: 12499
Price: Free* [*Free Regsitration Required]
Uploader: Kelrajas

The value shown is indicative only. At this time the flyback generator starts to supply the power output amplifier output stage by a diode inside the device. Pin 14 is the main supply voltage input VS positive.

Access Denied

Between the heatsink and the package, it is better to insert a tda16775a of silicon grease, to optimize the thermal tda167a no electrical isolation is needed between the two surfaces. Later, the increasing flyback current reaches the peak value and then the flyback time is completed: During the trace time the supply voltage is obtained from the main supply voltage VS by a diode, while during the retrace time this pin is supplied from the flyback generator.

EPS 8 spring clip being sufficient. The Sync input pulse at the Sync gate lowers the level of the upper threshold and than it controls the period duration. Flyback generator This circuit supplies both the power amplifier output stage and the yoke during the most tdz1675a the duration of the flyback time retrace. It is a full performance and very efficient vertical deflection circuit intended for direct drive of the yoke of o colour TV picture tubes.

Datasheets search archive of electronic components datasheets

The internal clock pulse stops the increasing ramp by a very fast discharge of the capacitor a new voltage ramp is immediately allowed. An external network, Ra and Rb, defines the DClevel across Cy so allowing a correct centering of the output voltage. EPS 5 tda1675 V1 12 9 12 5 A Td1675a mentioned in this publication are subject to change without notice. Pin 15 is the output of the flyback generator that, when driven, jumps from low to high condition.

VS 1 25 Pin 4 is the inverting input of the amplifier used as integrator. Power amplifier T his amplifier is a voltage-to-current power converter, the transconductance of which is externally defined by means of a negative current feedback. Pin 10 is the output of the buffer stage and it is internally coupled to the inverting input of the power amplifier through R1.

Related Posts  ZYGMUNT BAUMAN WASTED LIVES PDF

C 0 0 50 A Pin 13 is an open collector output where the blanking pulse is available. The supply of the power output stage is forced at this pin. The power output stage is thermally protected by sensing the junction temperature and then by putting off the current sources of the power stage. The internal clock opens the loop of the amplifier and lets pin 1 floating so allowing the rising of the flyback.

A capacitor must be connected to increase the performances from the noise point of view.

INTEGRATED CIRCUIT TDAA = A MULTIWATT 15

Pin 11 is the non-inverting input. Pin 9 is the output of the current mirror that charges the series of Ca and Cb.

However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use.

An integrated diode stops the rising of this tfa1675a increase and the voltage jump is transferred by means of capacitor Cf at the supply voltage pin of the power stage pin 2. Blanking generator and CRT protection This circuit is a pulse shaper and its output goes high during the blanking period or for CRT protection.

A clock pulse is generated. Pin 7 The resistance between pin 7 and ground defines the current mirror current and than the height of the scanning. Rights to use these components in tdz1675a I2C system, is granted provided tda16675a the system conforms to the I2C Standard Specifications as defined by Philips.

When the current across the yoke changes its rda1675a, the output of the flyback generator falls down to the main supply voltage and it is stopped by means of the saturated output darlington at a high level. This publication supersedes and replaces all information previously supplied.

TBL Dimensions Information furnished is believed to be accurate and reliable. An external capacitor Cf transfers the jump to pin 2 see pin 2. This pin is also the input of the buffer stage. Peak Output Current 0 0. I9 I14 V1 Figure 1: Crossing the main supply voltage at pin 14, the flyback pulse front end drives the flyback generator in such a way allowing its output to reach and overcome the main supply voltage, starting from a tva1675a condition forced during the trace period.

Related Posts  THE PLAYBOOK MIKE BELLAFIORE PDF

Pin 1 is the output of the power amplifier and it drives the yoke by a negative slope cur- Pin 2 rent ramply.

TDAA Datasheet ST Microelectronics pdf data sheet FREE from

If the flyback pulse is absent short cirucit or open cirucit of the yokethe blanking output remains high so allowing the CRT protection. Pin 12 is the inverting input of the amplifier. The internal clock turns off the lower power output stage to start the flyback. The output of the power amplifier pin 1 falls under the main supply voltage and the output of the flyback generator is driven for a low state so allowing the flyback capacitor Cf to restore the energy lost during the retrace.

The external components Rc, Ra and Rd, produce the linearity correction on the output scanning currentIy and their values must be optimized for each type of CRT.

The flyback generator supplies the yoke too. Re and the Boucherot cell are used to stabilize the power amplifier. At this pin the non-inverting input reference voltage supplied by the voltage regulator can be measured. The series network Rc and Cc, in conjunction with Ra and Rb, applies at the feedback input I2 a small part of the parabola, available across Cy, and AC feedback voltage, taken across Rf. The output stage of the power amplifier is supplied by the main supply during the trace period, and by the flyback generator circuit during the most of the duration of the flyback time.